Steel Fabrication and Welding Course
A workshop-based programme in cutting, joining and fabricating structural steel and light steelwork. Learners practise the main welding processes and learn inspection and quality checks so their work meets client and code expectations. TARGET…
- Course ID 022
- 3 weeks (15 training days)
- Nairobi
- Beginner
- Certificate
Course Overview
A workshop-based programme in cutting, joining and fabricating structural steel and light steelwork. Learners practise the main welding processes and learn inspection and quality checks so their work meets client and code expectations.
TARGET AUDIENCE
■ Fabricators and welders
■ Apprentices and technical school leavers
■ Maintenance technicians
■ Contractors with steelwork packages
- Duration
- 3 weeks (15 training days)
- Course fee
- KES 279,000
- Venue
- Nairobi
Course Requirements
Participants should have:
- ■ Minimum age of 18 years and a valid national ID
- ■ Basic numeracy and ability to read simple workshop drawings
- ■ Medically fit, with no uncorrected eyesight problems, for welding and workshop conditions
- ■ Own safety boots and overalls
- ■ No prior welding experience required; workshop experience is an advantage
Course Objectives
By the end of this course, participants will be able to:
- ■ Read fabrication drawings and weld symbols and prepare cutting lists.
- ■ Cut, shape and fit up steel sections accurately.
- ■ Weld in multiple positions using stick, MIG and TIG processes.
- ■ Inspect welds and fabricated items for quality and dimensional accuracy.
- PERSONAL IMPACT
- ■ Weld confidently in several positions with stick, MIG and TIG
- ■ Read fabrication drawings and weld symbols
- ■ Prepare for a welder qualification test
- PERSONAL IMPACT
- ■ Weld confidently in several positions with stick, MIG and TIG
- ■ Read fabrication drawings and weld symbols
- ■ Prepare for a welder qualification test
Course Modules
Module 1 Workshop Safety and Metals
- ■ PPE
- ■ Hot work and fire safety
- ■ Fumes and eye protection
- ■ Steel types and sections
Practical exercise: Inspect a workshop for hazards and complete a hot work and PPE checklist
Module 2 Drawings and Cutting Lists
- ■ Fabrication drawings
- ■ Weld symbols
- ■ Steel section tables
- ■ Material take-off and nesting
Practical exercise: Read a fabrication drawing, interpret its weld symbols and prepare a cutting list
Module 3 Marking Out and Cutting
- ■ Marking tools
- ■ Hand cutting and grinders
- ■ Oxy-fuel and plasma cutting
- ■ Accuracy checks
Practical exercise: Mark out and cut steel sections to a cutting list and check accuracy
Module 4 Drilling, Bending and Fit-up
- ■ Drilling and punching
- ■ Bending and forming
- ■ Clamps and jigs
- ■ Tack welding
Practical exercise: Drill, bend and tack-weld a small frame in a jig to dimension
Module 5 Welding Principles
- ■ Processes overview
- ■ Power sources and electrical safety
- ■ Electrodes and consumables
- ■ Joint types
Practical exercise: Select electrodes and set up a power source for given joints and justify the choices
Module 6 Stick Welding I
- ■ Arc striking
- ■ Bead runs in the flat position
- ■ Electrode selection
- ■ Reading the weld pool
Practical exercise: Run straight stick-weld beads in the flat position and assess them visually
Module 7 Stick Welding II
- ■ Fillet and butt joints
- ■ Horizontal and vertical positions
- ■ Root and cap runs
Practical exercise: Weld a fillet joint and a butt joint in horizontal and vertical positions
Module 8 Stick Welding III
- ■ Overhead welding
- ■ Position drills
- ■ Common defects and their causes
Practical exercise: Complete overhead weld exercises and diagnose defects from sample plates
Module 9 MIG/MAG Welding
- ■ Machine set-up
- ■ Gas and wire selection
- ■ Techniques on mild steel
- ■ Production welding
Practical exercise: Set up a MIG machine and weld a mild-steel joint to a given standard
Module 10 TIG Welding Basics
- ■ Equipment and tungsten preparation
- ■ Techniques on thin sections
- ■ Introduction to stainless steel and aluminium
Practical exercise: Prepare a tungsten electrode and run a TIG weld on a thin-section plate
Module 11 Distortion and Sequence
- ■ Heat effects and distortion
- ■ Welding sequence and balancing
- ■ Preheat and post-weld basics
Practical exercise: Weld a test assembly using a balanced sequence and measure the distortion
Module 12 Fabricating Structural Items
- ■ Gates and grilles
- ■ Stairs and handrails
- ■ Roof trusses and portal frames
Practical exercise: Fabricate a small gate or handrail section to drawing
Module 13 Quality and Inspection
- ■ Visual inspection
- ■ Weld gauges
- ■ Dimensional checks
- ■ Overview of dye penetrant and magnetic particle testing
- ■ Codes and acceptance criteria
Practical exercise: Inspect completed welds with weld gauges against acceptance criteria and write a short report
Module 14 Erection, Protection and Finishing
- ■ Bolted connections and torque
- ■ Painting and galvanising
- ■ Site installation
- ■ Working at height safely
Practical exercise: Bolt up a connection to torque, then paint and protect a fabricated item
Module 15 Capstone and Welder Test
- ■ Fabricate and weld a set piece to drawing
- ■ Practical welder test
- ■ Costing a fabrication job
Practical exercise: Complete a practical welder test piece and cost a fabrication job
Course Administration Details
Methodology
Training is hands-on. Most of the time is spent doing the work on our training site and on live projects, guided by experienced professionals. Short classroom sessions cover drawings, materials and safety. All sessions are in English.Certificate
Participants who complete the course and pass the final assessment receive a RailSite Fieldwork Academy certificate.Training Venue
Training takes place in Nairobi, at our training site and on active project sites. The course fee covers tuition and training materials. Participants cover their own transport, meals and other personal expenses.Group and Tailor-Made Training
We can run this course for your team, company or community group, at a date and location that suits you. Call or message us to plan it.Payment
Pay the course fee on or before the start date. Call +254 721 720 987 or email info@railsitebld.com for payment details.Intakes
Upcoming intake dates
Want this course for your team or group? Request group training.
